Eleaf iStick Basic Kit Instruction - Vape Manual

6:24 PM Unknown 0 Comments

Notice for Use Thank you for choosing Eleaf products! Please read this manual carefully before use so as to use correctly. If you require additional information or have questions about the product or its use, please consult your local agents, or visit our website at www.eleafworld.com



Product Introduction 

The iStick basic with the GS Air 2 atomizer is a new starter kit from Eleaf. Not only does the iStick basic have a large battery capacity of 2300mAh, it also features its innovative magnetic connector and atomizer built-in structure for ease of usage and carry. With a fashionable metallic appearance, the iStick basic also comes with many attractive colors for your options

How to Use

1) Assembling: 1.First screw the atomizer head onto the atomizer base tightly; 2.Next put together atomizer base, atomizer tube and mouthpiece;



3.Then screw the GS Air 2 atomizer onto the magnetic 510 connector tightly;
4.Finally put the GS Air 2 atomizer into the iStick basic.



2) E-liquid Filling: 1.First pull out the atomizer from the iStick basic; 2.Next unscrew the atomizer base off the atomizer; 3.Then slowly fill the e-liquid into the atomizer along the tube; 4.Finally screw the atomizer base onto the atomizer again.



Note:

a) Please don’t overfill and make sure the liquid level is between 10%-90%; b) Please first drip a few drops of e-liquid directly into the wick so as to make the atomizer head fully saturated before vaping.

3) Air Inflow Adjustment: The amount of air inflow can be easily adjusted by rotating the airflow control ring on the atomizer base so as to get different vaping experiences

4) Power on/off: Press the button five times in quick succession within two seconds, the white button light will flash five times to show the iStick basic is ready for use. In the same way, the device can also be turned off.

5) Vaping: Long press the button to take a puff.

6) Charging: Charge the device by connecting it with wall adapter or computer via the USB cable.

The button light will turn red when the device is charging and the light will go out when fully charged. It will take about three hours to get a full charge via 1A wall adapter.


Properties 

Atomizer Protection: When vaping time exceeds fifteen seconds, the device will shut off automatically with the white button light flashing ten times.

No Atomizer Protection: The white button light will flash slowly when the button is pressed down without atomizer connected.

Short-circuit Protection: Short-circuit occurs with the white button light flashing three times. Low-voltage Protection: When the voltage of device is below 3.3V, the white button light will flash 40 times. Charge the device to power it on.

Battery Level Indication Function: The white light will stay lit or flash slowly after a puff when the battery level is high. On the contrary, the light will flash in frequency.



Precautions 

1. Only have your iStick basic Kit repaired by Eleaf. Do not attempt to repair the unit by yourself as damage or personal injury may occur.
2. Do not leave the iStick basic Kit in high temperatures or damp conditions, otherwise it may be damaged. The appropriate operation temperature is within 0℃to 45℃ while charging and -10℃ to 60℃ while using.
3. Do not attempt to combine the iStick basic Kit with parts from other brands of e-cigarettes. If it is damaged in this way, our company will not take on responsibility and your warranty will be void.

Warranty
We are not responsible for any damages caused by human error. Legal warranty is applied.

0 comments:

Comment utiliser le kit Eleaf iJust3 - Manuel - Français

12:01 AM Admin 0 Comments

Comment utiliser? 



Mise sous / hors tension: appuyez sur le bouton 5 fois de suite, le voyant clignote 5 fois pour indiquer que l'appareil est sous tension. De la même manière, il peut également être mis hors tension. La couleur du voyant change en fonction de la capacité restante de la batterie, comme suit:


Vaping: 

maintenez le bouton enfoncé pour prendre une bouffée lorsque l'appareil est allumé. Lors de la vaporisation, le voyant reste allumé.

Chargement: 

l'appareil peut être chargé en le branchant avec un adaptateur mural 1A ou un ordinateur via le câble USB. Le voyant lumineux est rouge pendant le chargement et s'éteint lorsqu'il est complètement chargé.

Propriétés et protections: 


Plage de résistance: 0.1Ω-3.0Ω

Protection d'atomiseur: 

chaque fois que le temps de vape dépasse 15 secondes, le voyant clignote 10 fois et l'alimentation se coupe automatiquement.

Protection contre les courts-circuits: 

si un court-circuit survient avant le vapotage, le voyant clignote 5 fois et l'alimentation se coupe automatiquement lorsque vous commencez à vaper; Si un court-circuit se produit pendant le vapotage, le témoin clignote 3 fois.

Protection basse tension: 

lorsque la tension de l'appareil est inférieure à 3.3 V, le voyant clignote 40 fois et il n'y a pas d'alimentation lors du vapotage. Chargez l'appareil pour le réactiver.

0 comments:

How to Use Vaporesso SKRR Tank - User Manual

6:20 PM Unknown 0 Comments

PRODUCT COMPONENTS


MAIN FEATURES


● Innovative QF air distribution system   Eliminating cold air intake for warmer,    richer flavors, increasing and optimizing    the airflow to create even bigger and    denser clouds than ever before!
● No more spit back   The bullet-shaped inner structure    change the air flow to prevent liquid    from coming up through the drip tip.
● Best leak protection   By having the QF airflow and an    internal reservoir design, we have    minimized the leaking and maximized    the use of your e-juice by recycling any    that potentially lost.
● Flax Fiber with Cotton    Longer coil lifespan & more consistent    flavor !


● Simple Locking Mechanism on drip tip

SPECIFICATIONS

Refillable tank capacity: 8/2ml
Dimensions: 59.85 x 30 x 30 mm(8ml) / 59.85 x 27.8 x 27.8 mm(2ml)

HOW TO USE SKRR Tank


1. Adjustment of Air Flow 


The bottom airflow system can be adjusted by twisting the airflow ring.


2. Filling E-liquid 

Unscrew drip tip to unlock the tank, rotate lid on the direction indicator and then you can fill your favorite E-juice in.



3. Changing Atomizer

Remove base to unscrew the coil and insert the new one. Secure the base back onto the device. There are a variety of coils available for SKRR Tank. Please select the coil you desire.

WARNING: 1. When using a new atomizer, after filling in e-liquid, let the tank stand for 5 minutes, so the coil can be saturated with juice before firing. 2. Refill the tank before the tank becomes completely empty in order to avoid dry burnt or damage to the atomizer 3. Keep it out of reach of children and pet

This refillable electronic cigarette is intended for use with compatible liquid, which may contain nicotine. Nicotine is an addictive substance and its use is not recommended for use by the following:

- Non smokers or persons under the legal smoking age
- Pregnant or breastfeeding women
- Persons experiencing heart disease, stomach or duodenal ulcers, liver or kidney problems, long-term throat disease or difficulty breathing due to bronchitis, emphysema or asthm

0 comments:

Three Best BF Mod in 2018 - Vape Guide

1:05 AM Admin 0 Comments

For vapers who like RDA vaping, BF Mod is no stranger. This is a vape mod that brings more convenience to RDA vaping. It has the same features as the usual vape mod but has an extra e-juice bottle. With it, RDA Atomizer will not need to add e-juice frequently. You can add e-juice directly by simply squeezing the Bottle.



Many brands have launched their own BF Mod. Vandy Vape is a well-known DIY Vape brand. To cater to the use of BF Mod, the new RDA will be equipped with a BF Pin. You don't need to worry about your device being unusable. If you are interested in BF Mod, which one is the best BF Mod for you?


1.Vandy Vape Pulse X BF 90W Mod
2.Wismec LUXOTIC BF BOX Mod
3.Hugo Vapor Squeezer BF Mod

For more offers, please visit Cloumix.com

0 comments:

Is RDA Atomizer Suitable for Beginners? Vape Guide

7:31 PM Unknown 0 Comments

If you are trying out e-cigarettes for the first time, you will hear a lot of vapers recommend you to use the Pen Kit or Starter Kit. Both devices have a common feature and are easy to use. They all belong to the e-cigarette device out of the box, and we don't even need to install anything. So what is the experience of RDA Atomizer for beginners?



When the beginners touch the Starter Kit, it is effortless to get started. Some Pod Kits can be used directly without even a fire button. We are simply vaping, no need to think or do anything. The Starter Kit saves us a lot of time and the vaping experience is quite satisfactory. But, to be honest, RDA Atomizer will open a new world for you.



RDA allows users to build their coils. We are free to set the coil resistance we want, and the vaping experience brought by RDA will be even more impactful. For the beginners, RDA will make us feel a little trouble because we need to wrap the wire ourselves and need to install it ourselves. But the most important thing is that you will get a sense of accomplishment.

When you build a coil yourself, the vaping feeling it brings is beyond your imagination, and you will worship yourself. But for users who don't like to wrap their wires, Pre-Made Tank will be more suitable for you. It has not only excellent atomization but also is easy to replace. So what do you think? Which Atomizer do you prefer?

0 comments:

If Your Wismec DNA200 Has Encountered Some Problems

1:46 AM Admin 0 Comments

Q: What if the screen display "check battery"/ "weak battery"/ "battery low" after inserting fully-charged batteries? 


A: Firstly, please install other set of fully charged cells for a try.
Secondly, there is a small cotton like this in the device, please take out of it form the hole with tweezers. Then a screw will be shown, please tighten the screw.


Q: Why the file downloaded from your website can not be open?


A: You should download the Escribe software firstly and then related operation can be continued. And the link is http://www.evolvapor.com/.

0 comments: